Can I Set Up A Bathtub Myself?
Can I Set Up A Bathtub Myself?
Blog Article
What're your opinions concerning Tools You Need to Install a New Bathtub ?
Setting up a bath tub isn't precisely rocket science, however it does call for solid plumbing, woodworking, as well as sometimes, tiling abilities. Replacing an old tub with a new one is additionally a moderately hard task. If the old bathtub is readily available, the task can move speedily; if you need to open up a wall to remove the old bathtub as well as position the brand-new tub, the task is a lot harder. In either instance, the job is within a home handyman's abilities, although you will need an assistant to leave the old bathtub and also set in the brand-new one. Make certain you have certified yourself for the job and also are comfortable trying it. Instead of hiring a specialist to take over a halfway-completed task, it is much better to consider utilizing one prior to you begin. Chances are you might require an expert plumber to make tube connections.
This article will certainly aid you set up a new bathtub in your bathroom if you have actually currently purchased a new bathtub and also don't need to change the setup of your previous water system pipes.
Your tools and also product checklist should consist of the following:
Preparing for the Installment
First of all, the sustaining structure supplied with the bath needs to be fitted (if required) according to the maker's guidelines. Next, fit the taps or mixer to the tub. When suitable the tap block, it is essential to make certain that if the faucet comes with a plastic washing machine, it is fitted in between the bath and also the taps. On a plastic bathroom, it is also practical to fit a supporting plate under the taps device to avoid stress on the bath tub.
Fit the adaptable tap connectors to the bottom of the two taps utilizing 2 nuts and also olives (occasionally supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet via the hole in the bathroom. Make use of the nut supplied by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Make sure you use all of the supplied washers.
Connect the trap to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Connect the bottom of the overflow tube in a similar manner.The bath should now be ready to be fitted in its final position.
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your setup, after that the first thing you must do is detach the supply of water. After doing so, switch on the taps to drain any water remaining in the system. The procedure of getting rid of the existing faucets can be quite problematic as a result of the restricted access that is usually the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipes to the faucets. Have a towel prepared for the staying water that will come from the pipelines. As soon as the supply pipelines have actually been gotten rid of, utilize the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the single taps from transforming throughout this process. Once the faucets have actually been eliminated, the holes in the bath/basin will need to be cleaned up of any type of old sealing compound.
Prior to going on to fit the brand-new taps, compare the pipe links on the old faucets to the new taps. If the old taps are longer than the new faucets, after that a shank adapter is required for the new faucets to fit.
Mounting the Tub
Utilizing the two wooden boards under its feet, position the tub in the needed position. The wood boards are handy in uniformly spreading the weight of the bathtub over the location of the boards as opposed to focusing all the weight onto four tiny factors.
The next goal is to make certain that the tub is leveled all round. This can be achieved by inspecting the level as well as readjusting the feet on the tub till the spirit level checks out level.
To set up faucets, fit the bottom of the outermost flexible faucet connector to the suitable supply pipeline by making a compression join; after that do the same for the other faucet.
Switch on the water system and inspect all joints and also new pipework for leaks and also tighten them if necessary. Fill up the bath tub and likewise examine the overflow outlet as well as the regular electrical outlet for leakages.
Finally, take care of the bath paneling as defined in the producer's user's manual. Tiling and securing around the bath tub ought to wait till the bathtub has actually been made use of a minimum of when as this will settle it right into its last position.
Fitting New Touches
If the tails of the brand-new faucets are plastic, then you will require a plastic adapter to prevent damage to the thread. One end of the port fits on the plastic tail of the tap and also the various other end offers a link to the current supply pipes.
If you require to fit a monobloc, after that you will need minimizing couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next off, place the faucet in the mounting hole in the bath/basin guaranteeing that the washers remain in location in between the faucet and also the sink. Secure the tap in place with the producer supplied backnut. When the faucet is firmly in position, the supply pipelines can be attached to the tails of the taps. The taps can either be connected by using corrugated copper piping or with normal tap connectors. The former kind should be connected to the tap ends initially, tightening up just by hand. The supply pipelines can later be connected to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Bath tub
In the location where the bathroom satisfies the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is very important as the installation can move enough to break a stiff seal, causing the water to penetrate the wall surface in between the bathroom and also the tiling, bring about difficulties with dampness and possible leaks to the ceiling below.
You can pick from a selection of coloured sealers to assimilate your components and also installations. They are marketed in tubes and also cartridges, and also can securing voids as much as a size of 3mm (1/8 inch). If you have a bigger space to fill up, you can fill it with twists of soaked newspaper or soft rope. Remember to always fill up the tub with water before sealing, to enable the motion experienced when the bathtub remains in usage. The sealer can split relatively very early if you do not think about this activity prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are likewise quickly offered on the market. It is recommended to fit the ceramic tiles utilizing water-resistant or waterproof adhesive and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We hope you enjoyed our part on Installing A Bathtub. Many thanks for finding the time to read our posting. Loved our piece? Please share it. Let other people locate it. Thank-you for taking the time to read it.
Click On This Link
Report this page